現在很多家庭都安裝的地暖采暖,但是問題來了,該如何選用地板成了大家非常關注的話題,什么樣的地板才適合地暖呢?為此濟南塑膠地板小編給出了一些建議.由于地?zé)岵膳奶厥庑?對地板的要求非常嚴格,地?zé)釋Ｓ玫匕灞仨毦邆錈醾鲗?dǎo)性能好、熱穩定性能要好、環保性能要好、抗變形性好“四好”要求.
Now many families have installed floor heating, but the question is, how to choose floor has become a topic of great concern, what kind of floor is suitable for heating? For the Ji'nan small plastic floor and gives some suggestions. Because of the special nature of geothermal heating on board very strict requirements, special geothermal floor must have good heat conduction performance, thermal stability is better, better environmental performance, good deformation resistance "four good".
建議選擇復合地板.因?yàn)閺?fù)合地板的厚度大多在7——8mm,很容易將地?zé)嵯到y(tǒng)產生的熱量傳導至地表,而且復合地板的表面為金屬氧化物的耐磨層一,熱量在地表擴散得非?？於揖鶆?而實木地板比較厚,一般厚度在2cm左右,而且安裝時還要打龍骨,所以地?zé)嵯到y(tǒng)的熱量不易傳導到地表,而且木材的熱傳導系數非常低,這樣會導致熱量的浪費,也會使地表溫度不均勻,溫差感覺非常明顯.
Recommended to choose the composite floor. Because the thickness of the composite floor mostly in the 7 - 8mm, it is easy to generate geothermal system of heat conduction to the surface, and the surface of the composite floor of the wear-resistant layer of a metal oxide, diffusion of heat very quickly and evenly on the surface. The thick solid wood floor, usually about 2cm in thickness, and the installation of shihaiyaoda keel, so the geothermal system of heat conduction to the surface is not easy, and the wood thermal conductivity is very low, it will cause the waste of heat, but also make the surface temperature uniformity, temperature feeling is very obvious.
進口地板質量達到歐洲Enpr13329標準,國產地板質量達到GB/T1802-2000標準,都可以適應地?zé)岬匕灏惭b的技術要求,目前市場上一些合格品牌都達到了這一標準.鎖扣式地板的效果,因鉤聯地板間留有細小縫隙,所以膨脹后也不易走形.
The quality of imported floor to the European Enpr13329 standards, domestic floor quality meet the national standard GB/T1802-2000, can meet the requirements of geothermal floor installation technology, currently on the market some qualified brands have reached this standard. The lock type floor better, because a small gap left hook connection between plates, so easy to take shape after expansion.
為了增加導熱量,墊層材料和地板厚度不宜過厚,地?zé)岬匕宓臉?biāo)準厚度為6.5—8.5mm,強化復合地板應為6—8mm,三層實木復合地板8—9mm.建議消費者在謹慎選用的同時,盡量選用小尺寸,好是200×40×10拼成的方形或人字形,使其熱變形均勻.
In order to increase the heat conductivity, cushion material and thickness of the floor should not be too thick, geothermal floor standard thickness 6.5 8.5mm, composite floor should be 6 8mm, three layers of solid wood flooring 8 9mm. also suggested that consumers in careful selection, try to use small size, the best is 200 x 40 x 10 spell square or herringbone, the uniform thermal deformation.
